Installed roger wilco now UT crashes

  • Two Factor Authentication is now available on BeyondUnreal Forums. To configure it, visit your Profile and look for the "Two Step Verification" option on the left side. We can send codes via email (may be slower) or you can set up any TOTP Authenticator app on your phone (Authy, Google Authenticator, etc) to deliver codes. It is highly recommended that you configure this to keep your account safe.
J

JollyRoger666

New Member
Jun 10, 2001
12
0
0
Visit site
I just want to thank anyone who responds before hand, it's gotta suck helping a bunch of a**es, who don't know what their doing all the time.
System:
700mhz celeron processor
128 MB Ram
SB Live sound card
Geforce 2 32MB MX Vid card
Asus CUSL2-C mother board
Most of the driver are updated. Just got the new Nvidia drivers and my sound drivers aren't that old, haven't done the motherboard yet though. UT is patched to 436, I did however just download the EAX enhancement from Creative.

Problem:
Last night I installed Roger Wilco to try out. It worked OK at first, but after little while UT crashed, and I got a fatal exception OE at 0028:d633f42c message. I tried to reboot My computer and I got another fatal exception OE at 0167:B00DB560. Took 3 times to reboot!! After I finally got it rebooted, UT and roger wilco worked fine the rest of the evening. Now I think I should also mention that since I'v built this computer I have randomly ( I can count the # of times on one hand) gotten a fatal exception OE at 0167:BFF83BFC during start up, not all the time though. I don't know if they are connected or not. Now today when I tried to start UT It would not load The message it gave me said this was the reason:
UNREALTOURNAMENT caused an invalid page fault in
module <unknown> at 0000:b00db560.
Registers:
EAX=d5ef7000 CS=0167 EIP=b00db560 EFLGS=00010286
EBX=00000006 SS=016f ESP=0062c588 EBP=006285a2
ECX=00000e80 DS=016f ESI=d5ee8590 FS=015f
EDX=0062c580 ES=016f EDI=d5ef4aff GS=0000
Bytes at CS:EIP:

Stack dump:
00000f6d 0000034f 0000fbbe 80395400 016f2037 70000000 85bcd5ef 034f0fa4 00000e80 00000006 b00db560 00000167 d5eee000 44b985fa 0e80034f e0000000
Can anyone out their make sense of this, I lack the depth to understand all those numbers.
Thanks again
 
Swedix

Swedix

Retired from UT2004
Apr 19, 2000
4,853
0
0
In position
It seems you have some trouble with your PC that is not only UT related.
What version of BIOS do you have on your mobo?
Have you overclocked ?
If you run in higher fsb than 100 it might be your RAM which cause the crash or you must upper the vcore.

A very good site where you should go is
AsusBoards.com
I have a CUSL myself and got a lot of help from there.
 
J

JollyRoger666

New Member
Jun 10, 2001
12
0
0
Visit site
Ok I'm running version 6.0 on my bios and I am not overclocking.
I'm not sure about the rest, I don't think I understand the last part:"If you run in higher fsb than 100 it might be your RAM which cause the crash or you must upper the vcore. "

BTW I'm running Win 98 SE
 
Last edited:
Swedix

Swedix

Retired from UT2004
Apr 19, 2000
4,853
0
0
In position
Originally posted by JollyRoger666

I'm not sure about the rest, I don't think I understand the last part:"If you run in higher fsb than 100 it might be your RAM which cause the crash or you must upper the vcore. "

BTW I'm running Win 98 SE
Click to expand...

FSB - FronSideBus. That's the speed in Mhz on your CPU bus.
It's 100 MHz and the clock multiplier in your CPU is 7 so it run in 700 MHz. To overclock the cpu you higher the fsb. The CUSL2 board is very nice in that case.
That's about that.
Back to your problem.
Where did you d/l RW from?
Could you have been infected by virus?
You should scan your HD with the latest antivirus.
If you don't have virus you could have some hardware failur.
There is some programs you can run to test your hardware.
Check out Tweakfiles under Diagnostic.
 
GerbilJammer

GerbilJammer

Resident NOOb :D
Jan 25, 2001
399
0
0
44
Louisiana
im on win 98 se, but i dont have roger wilco installed and ran with ut.. i suggest a scandisk and degraf ( a through scandisk) and a virus scan before that... ill let ya know if i have ne probs maself, oh and make sure you close all other unnecessary apps b4 running UT
 
B

BubbaF150

New Member
Oct 17, 2005
2
0
0
Crashes at startup, in module <unknown>

Hey Jolly.

This problem started on my W98 system as well. There is a temporary fix of just deleting all cache files, and the Unrealtournament.LOG file. I am forced to do this just to start the game, it gets annoying:confused:

I think it all started when I added a new OpenGL driver and Edited the Unrealtournament.INI file. If you don't mind loosing custom settings for a fresh start, just delete the .ini file also. The original default Unrealtournament.INI file will be automatically created.

After a complete re-install of the software, I still got the error after copying these non-default and edited files over the originals:

OpenGLDrv.dll
OpenGLDrv.ini
opengldrv.int
Unrealtournament.ini

Maybe a different openGL driver or using the original would solve it, I did not care for the original OpenGL's performance, and went ahead with tewaking.

If deleting the unrealtournament.log file is the cure, then why is the file 0 bytes??

I might be missing something wtih that, i don't know the log's purpose.

I wish i can find more info on this, because i like the openGL support.
 
B

BubbaF150

New Member
Oct 17, 2005
2
0
0
Same problem 4 years later

Deathmaker said:
It's alive, IT'S ALIVE!!!
Click to expand...

I still play unreal tournament. Fairly new to me despite its age. JollyRoger666 seemed to have the same problem I did.

You're responding to the thread as well, so I guess you're later than me. 4 years and 23 Hours too late, OMG IT'S ALIVE. :lol:
 
You must log in or register to reply here.
Top Bottom