1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.
  2. Two Factor Authentication is now available on BeyondUnreal Forums. To configure it, visit your Profile and look for the "Two Step Verification" option on the left side. We can send codes via email (may be slower) or you can set up any TOTP Authenticator app on your phone (Authy, Google Authenticator, etc) to deliver codes. It is highly recommended that you configure this to keep your account safe.

i have no idea how to explain it, just look...

Discussion in 'Level Editing - Advanced' started by lucifix, Dec 10, 2001.

  1. lucifix

    lucifix I did something m0tarded and now I have read only access! :(

    Joined:
    Nov 3, 2001
    Messages:
    2,427
    Likes Received:
    1
    ok, i have this arch/doorway thats giving me problems. on one side of it you can see a wall but you can walk through it. from the opposite side you can see staight through to the hallway.........
     
  2. lucifix

    lucifix I did something m0tarded and now I have read only access! :(

    Joined:
    Nov 3, 2001
    Messages:
    2,427
    Likes Received:
    1
    the side where you see the "wall".....
     
  3. Chrysaor

    Chrysaor Lord of the Pants

    Joined:
    Nov 3, 2001
    Messages:
    3,020
    Likes Received:
    4
    Your brushes don't line up, try moving the curved hallway closer to the doorjam. just look at the top view, and try "resetting" the snap, but clicking on the brushes and then right clicking on a corner, that's if they look like they already should touch.
    I don't make much sense i know.
     
  4. lucifix

    lucifix I did something m0tarded and now I have read only access! :(

    Joined:
    Nov 3, 2001
    Messages:
    2,427
    Likes Received:
    1
    that didnt work.........

    i took out the curved hallway and replaced it with a 256 cube and it does the same thing too.........
     
  5. Chrysaor

    Chrysaor Lord of the Pants

    Joined:
    Nov 3, 2001
    Messages:
    3,020
    Likes Received:
    4
    Is the trim a semi-solid?

    i honestly have no idea then. try redoing both brushes ?
     
  6. lucifix

    lucifix I did something m0tarded and now I have read only access! :(

    Joined:
    Nov 3, 2001
    Messages:
    2,427
    Likes Received:
    1
    the door trim? yes its semisolid
     
  7. Chrysaor

    Chrysaor Lord of the Pants

    Joined:
    Nov 3, 2001
    Messages:
    3,020
    Likes Received:
    4
    ah, well try it as a solid

    *crosses fingers*
     
  8. lucifix

    lucifix I did something m0tarded and now I have read only access! :(

    Joined:
    Nov 3, 2001
    Messages:
    2,427
    Likes Received:
    1
    ive tried solid, semisolid and non solid.........
     
  9. Chrysaor

    Chrysaor Lord of the Pants

    Joined:
    Nov 3, 2001
    Messages:
    3,020
    Likes Received:
    4
    hmmm...well...****.

    i'd just get pissed and redo it, but if that didn't work i wouldn't know what to do :(

    maybe someone else will give some advice...
     
  10. Luv_Studd

    Luv_Studd Member

    Joined:
    Aug 17, 1999
    Messages:
    822
    Likes Received:
    6
    kinda fugly texturing, but that's not your immediate problem apparently. ;)

    when you place the door way (subtracted brush) between two other subtracted brushes, presumably your trying to keep your brush sizes consistent factors of 8, and they line up properly to the grid. rebuild the map between each step.

    if anything else, it might be some surrounding brushes causing problems. hard to tell not knowing.

    :shock:
     

Share This Page